|Published (Last):||18 March 2013|
|PDF File Size:||6.39 Mb|
|ePub File Size:||14.1 Mb|
|Price:||Free* [*Free Regsitration Required]|
Quick Links. Table of Contents. Page 2 Warning - For Your Protection: 1. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. These symbols are internationally accepted symbols that 7. Vice-President of Engineering S.
Page 4: Warranty In no event shall Digitech or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control. III Effects IV Chorus You now have the flexibility, and power to produce sonic creations never before thought possible. Page 9 1. The Footswitch on the right will increase, and the Footswitch on the left will decrease the selected Preset.
Pressing both Footswitches together will bypass the currently selected Preset. Pressing and holding both Footswitches will access the Tuner. Page 10 6. Display - The Display provides information for different functions depending on the mode that has been selected. In Performance mode, the Display will show the currently selected Preset name and number.
In Edit mode, the Display will show the name and value of the parameter being adjusted. There is no power switch on the RP Artist.
Page Applying Power Applying Power Before applying power to anything, set your amp s to a clean tone and set the tone controls to a flat EQ response on most amps, this would be 0 or 5 on the tone controls. Then follow the steps listed below. Turn the amp volume all the way down.
The User Presets are locations where your creations may be stored. The Factory Artist and Factory Presets will not allow you to store any changes to them.
Enter Tuner mode by pressing and holding both Footswitches simultaneously. The Display will briefly show indicating that you are in Tuner mode. To begin tuning, play a note on your guitar a harmonic at the 12th fret usually works best. The Display shows the note being played. When creating or editing a sound, you must first start with one of the User or Factory Presets. It is not possible to start with a completely empty Preset. The Preset number does not necessarily need to be the location which you intend to have it reside, as you can save your creation to any User Preset location during the store process.
In Edit mode, successive presses of the Select button will advance to the next Effect row. The LED will light indicating which Effect group has been selected.
Each Effect group will have up to 3 Parameters which can be modified. The Knob under each column of Parameters is used to change the value for the corresponding Parameter of the selected Effect. The following steps outline the procedure for storing changes to a Preset or copying a Preset to a different location: 1. Page 20 5. Press the Store button again to save the changes.
The procedure for copying one Preset to another Preset location is the same. Use the Footswitches to select the Preset that you want to copy, then follow the steps for storing a preset on the previous page. With stomp boxes, the order in which they are connected can drastically affect the overall sound quality. The RP Artist has placed the Effects in an order for optimum sound quality.
The following diagram shows the order of the effects contained in the RP Artist. This allows you to have the best of both worlds without having to change guitars during a performance. Fender, Matchless, and Mesa Boogie, are trademarks of their respective companies and are in no way associated with DigiTech. The Gain parameter ranges from These settings will automatically ramp up the volume from a milliseconds volume fade in to a 2 second volume fade in.
When the Effects row is selected, the Parameter 1 knob is used to choose the type of Effect or turn the Effect module off. Page Phaser Phaser A phaser splits the incoming signal, and then changes the phasing of the signal.
This signal is then taken in and out of phase and mixed back in with the original signal. As the phasing changes, different frequencies get canceled resulting in a warm sort of twisting sound. Amount - The Parameter 2 knob simultaneously adjusts the rate Speed and intensity Depth of the Effect. It makes your guitar seem to be speaking based upon the attack or how hard you strike the strings. Page Detune Detune A Detuner will make a copy of your incoming signal, take the copied signal slightly out of tune from the original, and mix the two signals together.
The result is a doubling type of effect as if two guitars were playing the same part together. Amount - The Parameter 2 knob adjusts the amount of pitch difference applied to the copied signal. Page Delay Harmony Bends Dry Signal Added Whammy no Dry Signal a minor third to a Major third 1 octave above a second above to a Major third above 2 octaves above a third above to a fourth above a second below a fourth above to a fifth above a second below reversed pedal action a fifth above to an octave above Page Reverb Reverb Using reverb in recorded program material gives the listener a sense that the material is being performed in an actual room or hall.
It is this similarity to actual acoustic spaces that makes reverberation a useful tool in recorded music. Pressing the Drums button will enable the drum machine and start playback of the selected drum pattern except when in Store or Bypass mode.
When Drums is active, the Parameter 1 knob selects the drum Pattern, the Parameter 2 knob adjusts the drum Tempo, and the Parameter 3 knob adjusts the Level of the drum pattern. This procedure will erase all custom user Presets, and recalibrate the Expression Pedal. All such data will be lost forever! Be sure you want to erase the memory and start fresh before continuing with this procedure. This calibration procedure is automatically entered after a factory reset procedure.
This will not erase the User Presets. Print page 1 Print document 40 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.
DigiTech RP200 User Manual
Near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. It is your key to unlocking the potential within the RP The Footswitch on the right will increase, and the Footswitch on the left will decrease the selected Preset. Pressing both Footswitches together will bypass the currently selected Preset. Pressing and holding both Footswitches will access the Tuner.
DigiTech RP200A User Manual
Quick Links. See also: User Manual. Table of Contents. Page 2 Warning For your protection, please read the following: Water and Moisture: Appliances should not be used near water e. Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. Page 4: Warranty In no event shall Digitech or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control. It is your key to unlocking the potential within the RP